![Cisco usb console driver windows 10 64 download](https://knopkazmeya.com/11.png)
- #Cisco usb console driver windows 10 64 download install#
- #Cisco usb console driver windows 10 64 download serial#
- #Cisco usb console driver windows 10 64 download driver#
- #Cisco usb console driver windows 10 64 download Pc#
#Cisco usb console driver windows 10 64 download driver#
#Cisco usb console driver windows 10 64 download Pc#
Installing the Cisco Microsoft Windows USB Device DriverĪ USB device driver must be installed the first time a Microsoft Windows-based PC is connected to the USB console port on the switch. Follow the steps in the "Configuring the Setup Program" section. Step 6 The PC or terminal displays the bootloader sequence. Step 5 Connect power to the switch as described in Chapter 3 "Power Supply and Fan Module Installation.". Step 4 Configure the baud rate and character format of the PC or terminal to match the console port default characteristics: The program, frequently a PC application such as HyperTerminal or ProcommPlus, makes communication between the switch and your PC or terminal possible. Step 3 Start the terminal-emulation program on the PC or the terminal. Connect the other end of the cable to the switch mini-B (5-pin-connector) USB console port. Step 2 Connect a USB cable to the PC USB port. – "Installing the Cisco Microsoft Windows Vista and Windows 7 USB Driver" sectionįigure C-1 Connecting the USB Console Cable to the Catalyst 3750-X or 3560-X Switch – "Installing the Cisco Microsoft Windows 2000 USB Driver" section – "Installing the Cisco Microsoft Windows XP USB Driver" section
#Cisco usb console driver windows 10 64 download install#
Step 1 If you are connecting the switch USB console port (see Figure C-1) to a Windows-based PC for the first time, install the USB driver. The USB mini-Type B port is on the front panel of the switch.
![cisco usb console driver windows 10 64 download cisco usb console driver windows 10 64 download](https://phukienpc.vn/wp-content/uploads/2019/07/cap-console-usb-cisco-mini-5pin-1-8m-phukienpc-vn-1-1.jpg)
![cisco usb console driver windows 10 64 download cisco usb console driver windows 10 64 download](https://fishingever630.weebly.com/uploads/1/3/3/9/133913449/722681472.jpg)
Step 5 The PC or terminal displays the bootloader sequence. Step 4 Connect power to the switch as described in Chapter 3 "Power Supply and Fan Module Installation." Step 3 Configure the baud rate and character format of the PC or terminal to match the console port characteristics: The program, frequently a PC application, such as HyperTerminal or ProcommPlus, makes communication between the switch and your PC or terminal possible. Step 2 Start the terminal emulation program on the PC or the terminal. Connect the other end of the cable to the switch console port.
#Cisco usb console driver windows 10 64 download serial#
Step 1 Connect the RJ-45-to-DB-9 adapter cable to the 9-pin serial port on the PC. The RJ-45 console port is on the rear panel of the switch. Use one of these options to access the CLI: You can perform the initial configuration for the entire stack on any switch in the stack. Note If you have stacked Catalyst 3750-X switches, connect to the 10/100 Ethernet management port or console port of one of the stack switches. You can enter Cisco IOS commands and parameters through the CLI. You lose the Telnet connection after entering the write memory command.įor more information about using the CLI, see the command reference for this release. Note While in Express Setup mode, the IP address 10.0.0.1 remains active on the switch until you enter the write memory command. Īfter you have entered the configuration information for the switch, save it to flash memory by using the write memory privileged EXEC command. Enter the information described in the "Entering the Initial Configuration Information" section. When the switch is in Express Setup mode, open a Telnet session to the switch by entering the IP address 10.0.0.1. To put the switch into Express Setup mode, follow the steps described in the getting started guide for powering on the switch and using Express Setup.
![cisco usb console driver windows 10 64 download cisco usb console driver windows 10 64 download](https://media.startech.com/cms/products/thumb/icusb2321f.main.jpg)
![cisco usb console driver windows 10 64 download cisco usb console driver windows 10 64 download](https://sc02.alicdn.com/kf/HTB1SZtlb.gQMeJjy0Fgq6A5dXXaY/ftdi-pl2303-black-color-console-cable.jpg)
You can access the CLI on an unconfigured switch by placing the switch in Express Setup mode and then connecting a switch Ethernet port or the Ethernet management port to the Ethernet port of your PC or workstation. Before connecting the switch to a power source, review the safety warnings in Chapter 2 "Switch Installation." Accessing the CLI Accessing the CLI Through Express Setup To set up the switch by using Express Setup, see the Cisco 3750-X and 3560-X Switch Getting Started Guide. This appendix provides a CLI-based setup procedure for a Catalyst 3750-X and 3560-X standalone switch or a switch stack. Configuring the Switch with the CLI-Based Setup Program
![Cisco usb console driver windows 10 64 download](https://knopkazmeya.com/11.png)